 CDI-6050W |
|
CDI-6050W |
 Call
for current prices with the following list of equipment.In house training as explained below. Table size is 0.6 meter wide (23.6"). Table is 0.5 Meters deep. ( 19") Two high pressure air driven Graco stainless steel resin pumps and metering systems. One high pressure air driven Graco solvent washing pump. Dual purging stainless steel pans, with removable cover on left side of doming table. Optional auto purging. Emergency purging is case of power failure. CNC console for easy operator control. Complete Color-Dec programming software that is very user friendly. Approximately 50 ft of our own rislan tubing to go to the dispensing needles. 30 needles to go into the supplied tubing. Ten brass needle holders. One 1 to 3 splitter, and 3 two way splitters. One support bar for the needle holders. Necessary wrenches and tools for the machine. ( set of metric allen wrenches), One 6 in. and one 10 in. adjustable wrenches. One drum wrench to open drums. One small carpenters level. Two cans of oil. One roll of teflon tape. All nitrogen tubing and fittings to go from the CDI-6050 W to the two resin drums. Small amount of air line for main air hook up and solvent pump.  Additional auxiliary
equipment supplied in USA by Color-Dec InternationalOne 8 ft. (2.44m) very stable and strong aluminum leveling table. ( supplied in KD form requires about 30 minutes for two person assembly) 25 Aircraft Honeycomb Aluminum 1/4 thick stacking trays with standoffs assembled. 18.5 in. (44.45cm) x 23.5 in.59.7cm). One staking pallet. A dust free room adequately air conditioned and ventilated not smaller than 300 sq. ft. Recommended at least 500 sq. ft. ( 50 sq. m) WE WILL NOT SELL THIS MACHINE WITHOUT ADEQUATE TRAINING BY OUR STAFF. IF YOU CAN SCHEDULE THE START UP WHEN AN ITALIAN ENGINEER IS PRESENT IN THE USA THEN THE BUYER IS RESPONSIBLE FOR AIR FARE FROM THE PREVIOUS LOCATION TO YOUR LOCATION AND RETURN ONLY. ONE DAY FOR INSTALLATION WITH YOUR PERSONNEL IS NORMALLY ENOUGH. Two completer dcays of training is normally enough to adequately train your operators and forman on the workings of this model. If additional time is required for no fault of yours you will be charged $500 for a half day and $1000 for full day. THIS MACHINE IS BUILT IN ITALY AND FULLY GUARANTEED by them and C-D International AGAINST DEFECTS IN WORKMANSHIP FOR 12 MONTHS AFTER INSTALLATION under circumstances of normal use. Any non normal usage of the machine will negate this warranty. TERMS ARE 50 % WITH ORDER. 40 % AFTER INSTALLATION. 10 % AFTER 30 DAYS. Delivery is from stock and by truck, FOB Pitman, NJ. via Yellow Freight ( normally a SGIA 30 % discount applies). Equipment required to be supplied by customer and be in place before training can start: One bottle of Dry Nitrogen (Hospital quality). Ceiling mounted Hepa Filters at least one two ft. x four ft. for mounting over the leveling table. A 2500 CFM exhaust fan with pick up flex mounted over head the CDI-6050 W VACUUM TABLE Five gallons of either Methylene Chloride solvent or Acetone for cleaning the mixer and distributor, tubing and needles. This must be in a metal drum with a 2" NPT hole to mount the solvent pump. Approximately 1 cup of solvent is required to purge clean the static mixer, dispensing head, nozzles, tubing and needles. NOTE: A non toxic safe solvent is available from C-D International, quoted on request. One gallon (4 Liters) of Isopropyl Alcohol, sufficient lint free wipers, safety glasses , Lint free Tyvek™ work smocks for the employees. approx. $30 for 8) http://www.Granger.com/Granger/productdetail.jsp?xi=xi&ItemId=1611606759 Granger Item No. 4T053 Call for current pricing on our best turn key buy. - |
For More Information
Email: scott@color-dec.com
VISITORS
Home | What Is Crystal Drops | Resin Specifications | Auxiliary Equipment | Training
CDI-500W | CDI-6050W
| CDI-6000W | CDI-7000W
CDI-5000 | CDI-500